Mobile/Whatsapp

+86-15922982738

E-mail

gold20@hy-industry.com
Products
Home / Products / Industry / Wire & Cable / IEC 60332-1 Flame Propagation Test for Single Cable

Product Category

loading

Share to:
sharethis sharing button

IEC 60332-1 Flame Propagation Test for Single Cable

IFlame Propagation Test for Single Cable comply with IEC 60332-1. It is used to test the flame retardant properties of the insulation layer of wires and cables under abnormal conditions such as overheating or overcurrent.
Availability:
Quantity:
IEC 60332-1 Flame Propagation Test for Single Cable
  • GD-IEC60332

  • GOLD

  • 9031809090

IEC 60332-1 Flame Propagation Test for Single Cable

IEC 60332-1 Flame Propagation Test for Single Cable

   Introduction:   

Wire and Cable is second-largest industry. Single wire and cable vertical burning tester is the most widely used and low cost of cable fire performance test equipment. Single wire or cable burning tester meet the national standard GB /T18380.11-2008 / IEC60332-1-1: 2004 requirement. It is to test flame retardant insulation layer under fire conditions applicable for testing wire and cable in overheating, over-current and other non-normal state. It can be used for vertical or fiber optic wire and cable flame spread test,and test combustion conditions of Dettol matter under fire conditions.



   Standard:   

  IEC 60332-1-1,2,3
  EN 50086-1-1994
  GBT 18380.11,12-2008 



   Main features:   

1.  Touch screen intelligent control system; English user interface.

2.  Automatic ignition system, automatic timing, automatic data storage.

3.  The test section and the control section is combined design in one box for operation.

4.  Stainless steel test box, the internal cavity size: height 1200mm,width 300mm, depth of 450mm.

5.  A pre-mixed burner, an inner diameter of ¢ 12 ± 0.5mm, length is 100mm. 1KW hybrid standard burner,which provides accurate test fire source.

6.  The flame burning applied time and hold time can range from 0 to 99 minutes99 seconds range adjustment. Automatic control of the testing process.

7.  Needle valve precisely adjust the flame height, according to standards, the blue flame height is 50mm ~ 60mm, total height 170mm ~ 190mm.

8.  The gas flow rate is controlled by needle valve.

9.  Equipped with a flame height caliper.

10.  Equipped with a gas flow meter and pressure regulator; automatic ignition.

11.  The torch angle is 45 °, 0 ° adjustable.

12.  The flame calibration device is optional.

IEC 60332-1 Flame Propagation Tester

GD-IEC60332-1 Single Cable Flame Propagation Tester

IEC 60332-1 Flame Propagation Tester for Single Cable

GD-IEC60332-1 Single Cable Flame Propagation Tester

IEC 60332-1 Cable Flame Propagation Tester

GD-IEC60332-1 Single Cable Flame Propagation Tester



   Specifications:   

Operating voltage

AC220 V ± 10V 50HZ

Ambient temperature

room temperature ~ 40 ℃

Gas Pressure

0.1MPa

Gas purity

Propane> 95%; compressed air

Timing Accuracy

0.1s

 Model

GD-IEC60332

 Size

600(W)×450(D)×1250(H)mm

 Power

AC 220V, 50/60Hz, 3A

 Weight

60kg

 Manual

Provide



   Welcome to contact us:  

Contact Person: Kiana Feng

Whatsapp/Wechat: +86 15922982738

Mobile: +86 15922982738

Fax: +86-23-62940030

Email: gold20@hy-industry.com


Previous: 
Next: 
Send Us A Message

  Site Map

Contact Us

  25F, China Resources Building, Xiejiawan, Jiulongpo DistrictChongqing,China
  +86-23-62984892
  +86-15922982738
   
gold20@hy-industry.com
  +86-23-62940030

Quick Links

Send Us A Message

​Copyright © 2018  Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd. All Rights Reserved.